1996 Toshiba TMD-13
CNC Lathes
CNC Lathes
Toshiba TMD-13
5 Toshiba TMD-13 listings have come through the used market we track: 3 marketplaces, built 1995–1996 where given; 4 machines once repeats are merged.
63 inSwing
What the maker publishes about the current Toshiba TMD-13
Shibaura Machine, formerly Toshiba Machine, lists the TMD-13 as a vertical boring and turning mill with a live spindle. The swing and cut figure is 1,600 mm (63 in) and the cut height is 1,100 mm (43.3 in). The Z stroke is 800 mm (31.4 in), the X stroke runs from minus 630 mm to 920 mm, and the crossrail has 500 mm of vertical travel that is not an NC axis. The table size is 1,250 mm (49.2 in); it turns up to 450 rpm and carries 8,000 kg (17,600 lb). The live spindle head is rated 30/20 hp and turns 25 to 3,000 rpm on a 7/24 taper No. 50 shank. The magazine holds 24 tools and the control is a FANUC 31iB. Coolant through the spindle is standard. The bed is cast iron with ribs that support the whole table, the layout is thermally symmetrical, and a lubricant oil cooling unit is standard. A portable handwheel feed unit covers the X, Z and C axes. Scale feedback on those three axes, a pallet changer for two, four, six or eight pallets, a Renishaw touch probe and a Renishaw tool length probe are optional.
Source: Shibaura Machine, October 14, 2026.
What the Toshiba TMD-13 is used for
Shibaura Machine bases its TMD series on the TUD vertical turning mills and adds milling and table indexing, so a part clamped on the TMD-13 table can be milled, bored, drilled and tapped as well as turned in the same setup.
Source: Shibaura Machine, October 27, 2026.
Toshiba TMD-13 specifications
Manufacturer specification. Read from the manufacturer’s published specification and checked against it word for word.
Figures as currently published; an older unit may differ in control generation and options.
Capacity and travels
Max turning diameterSwing/Cut inch(mm)
63 in (1,600 mm)
Max turning lengthCut Height inch(mm)
43.3 in (1,100 mm)
X-axis travelX Stroke inch(mm)
-24.8 ~ 36.2 in (-630 ~ 920 mm)
Z-axis travelZ Stroke inch(mm)
31.4 in (800 mm)
Spindle and speed
Max spindle speedTable RPM
450 rpm (table)
Spindle motor powerLive Spindle (25 ~ 3000 RPM)
AC 30/20 HP, 25 ~ 3,000 rpm (live spindle head)
Spindle taper7/24 taper No. 50
7/24 taper No. 50
Table, turret and tools
Table sizeTable size inch(mm)
49.2 in (1,250 mm) diameter
Max table loadMax. load lbs(kg)
17,600 lb (8,000 kg)
Tool capacityATC Tool Pod
24 tools
Control
Control
FANUC 31iB
Further figures the manufacturer publishes
ARM/Crossrail Vertical Travel Not NC-Axis inch(mm)
19.7 in (500 mm), not an NC axis
- manufacturer specification page, fetched September 16, 2026.
What fits a Toshiba TMD-13
Each of these follows from a published specification above, which is named beside it.
50-taper toolholders
This is a 50-taper spindle — the 7:24 steep taper that CAT-50, BT-50 and DIN 69871 (SK-50) holders all share. They share the taper and nothing else that matters: the retention knob and the flange form differ between those standards, so holders do not swap between them without changing pull studs. Knowing which standard a machine was tooled for is worth doing before the holders are packed.
Derived from Spindle taper: 7/24 taper No. 50
Toshiba TMD-13 equipment and options
Standard on a new Toshiba TMD-13
- Through-spindle coolant
Optional on a new Toshiba TMD-13
- Pallet changer
- Pallet pool
- Tool probe
- Part probe
- Linear scales
Source: Shibaura Machine, October 26, 2026.
What to check on a Toshiba TMD-13
- Control generation. The manufacturer specifies FANUC 31iB for this model. Units we have tracked run 1995 to 1996; an early one may carry an older control or a retrofit.
- Table drive. The manufacturer gives a table speed of 450 rpm (table). Run the table to top speed and listen for bearing noise.
- Spindle load. The manufacturer gives AC 30/20 HP, 25 ~ 3,000 rpm (live spindle head) of spindle power. Take a heavy cut and watch the load meter.
- Spindle taper. The manufacturer gives a spindle taper of 7/24 taper No. 50. Check it for fretting and that the drawbar holds a tool.
- Axes and way covers. The manufacturer gives X -24.8 ~ 36.2 in (-630 ~ 920 mm) and Z 31.4 in (800 mm) of travel. Run each axis end to end and check the way covers.
- Tool changer. The manufacturer gives the tool capacity as 24 tools. Cycle every pocket and watch for a hesitation.
- Table. The manufacturer gives a table size of 49.2 in (1,250 mm) diameter and a table load of 17,600 lb (8,000 kg). Check the table and its T-slots for damage.
- Bed and ways. The manufacturer gives a max turning diameter of 63 in (1,600 mm) and a max turning length of 43.3 in (1,100 mm). Check the ways for wear near the chuck.
Toshiba TMD-13 control
- Control FANUC 31iB
Toshiba TMD-13 listing history
Where it was listed
exapro.com
2 listings
usedcnc.com
2 listings, 1995
machnet.com
1 listing, 1996
Sellers also filed it under CNC Vertical Boring Mills (1).
Model years seen
1996, 1995 ×2.
What Toshiba TMD-13 listings agree on
Swing
63 in
What affects the value of a used Toshiba TMD-13
- Control. The manufacturer specifies FANUC 31iB.
- Build year. The units we tracked were built from 1995 to 1996, across 2 model years, most often 1995 (2 units).
- Against the published figures. The manufacturer gives max spindle speed 450 rpm (table), spindle motor power AC 30/20 HP, 25 ~ 3,000 rpm (live spindle head), tool capacity 24 tools and max turning diameter 63 in (1,600 mm).
Looking for a Toshiba TMD-13 for sale?
We have tracked 5 Toshiba TMD-13 listings on 3 marketplaces (exapro.com, usedcnc.com and machnet.com), model years 1995 to 1996. We buy Toshiba TMD-13 machines and do not sell them.
Every Toshiba TMD-13 we have tracked
1995 Toshiba TMD-13
CNC Lathes
1995 Toshiba TMD-13
CNC Vertical Boring Mills
2 more listings, no year.
The Toshiba TMD-13 among lathes and turning centers
Browse all CNC Lathes, or see every Toshiba machine we track.
Models related to the Toshiba TMD-13
Toshiba TMD-20
Same series
Other CNC Lathes models in this directory
Toshiba TUE-150S
- Units tracked
- 8
- Years seen
- 2013–2021
- Max turning diameter
- 78.7 in (2000 mm)1this model: 63 in (1,600 mm)2
- Tool capacity
- 181this model: 24 tools2
Doosan VT 1100
- Units tracked
- 16
- Years seen
- 2007–2020
- Max turning diameter
- 1100 mm (43 inch)3this model: 63 in (1,600 mm)2
- Max turning length
- 960 mm (38 inch)3this model: 43.3 in (1,100 mm)2
Doosan V8300
- Units tracked
- 13
- Years seen
- 2016–2023
- Max turning diameter
- 830 mm (33 inch)4this model: 63 in (1,600 mm)2
- Max turning length
- 780 mm (31 inch)4this model: 43.3 in (1,100 mm)2
Toshiba TUD 20
- Units tracked
- 3
- Years seen
- 1996
Toshiba TUE-200
- Units tracked
- 5
- Years seen
- 2009–2012
- Tool capacity
- 185this model: 24 tools2
- Max table load
- 15000 kg5this model: 17,600 lb (8,000 kg)2
- Toshiba TUE-150S: manufacturer specification page, fetched October 14, 2026.
- Toshiba TMD-13: manufacturer specification page, fetched September 16, 2026.
- Doosan VT 1100: manufacturer specification page, fetched October 14, 2026.
- Doosan V8300: manufacturer specification page, fetched October 14, 2026.
- Toshiba TUE-200: manufacturer specification page, fetched October 28, 2026.
Have a Toshiba TMD-13 to sell?
We are the buyer, not a broker. No listing, no consignment, no waiting for someone else to find a buyer. Quote in 24 to 48 hours, and we can arrange rigging, freight and the pickup.
