Mazak QTN-200MSY-II
Manufacturer specifications, what it is built to do, the years we have seen them listed, what tooling fits, and what to check on one. MTE also buys them outright.
What the Mazak QTN-200MSY-II is
The Mazak QTN-200MSY-II is a CNC turning center — a machine for turning round parts between a chuck and, where fitted, a tailstock — shafts, flanges, housings and bar work. The manufacturer publishes a max turning diameter of 14.750 in / 380 mm. This one is specified with a Y axis, live tooling, a sub-spindle and bar work: off-center milling without a second setup; driven tools in the turret or milling spindle; the part transfers and is finished on the back end; a bar feeder can run stock through the spindle.
What it is built to do
From the figures the manufacturer publishes, a Mazak QTN-200MSY-II suits:
- bar work up to 2.6 in / 65 mm fed through the spindle
- parts finished on the back end without a second setup (second spindle, 6 in chuck)
- drilled, tapped and milled features on a turned part (rotary-tool upper turret, 4500 rpm)
- off-center features, on 4.00 in / 102 mm of Y travel
Mazak QTN-200MSY-II specifications
Source: archived manufacturer page.
One manufacturer document behind these figures is hosted on a third-party site rather than the manufacturer’s own, so it is recorded in our sourcing record rather than linked.
What fits a Mazak QTN-200MSY-II
Each of these follows from a published specification above, which is named beside it.
Workholding
An 8-inch chuck. Jaw sets, soft jaws and collet chucks for this size are commodity items, but the chuck itself, and any spare jaws, travel with the machine and are counted in an offer.
Derived from — Chuck size: 8 in
Bar feeder fit
Bar capacity is 65 mm, so a bar feeder for this machine has to be sized for stock up to that diameter. A feeder that comes with the machine is one of the accessories that most changes what a buyer will pay for it.
Derived from — Bar capacity: 2.6 in / 65 mm
What years the Mazak QTN-200MSY-II was built
Across the units we have tracked, build years run from 2006 to 2015. Observed across 25 marketplaces, not a manufacturer build record. The manufacturer specifies Matrix Nexus, so a unit on an older control is an early one or a retrofit.
Mazak QTN-200MSY-II machines on the market now
We track listings across 25 used-machinery marketplaces, and every competitor in this market is one of them, so this is a view none of them can produce for themselves. Right now there are 7 units of this exact designation on the market, drawn from 3 independent sources, spanning model years 2006 to 2015. A seller is competing with those units, which is why condition, tooling and control generation decide the number.
We count only listings whose model is spelled as this machine’s own designation. Near spellings that may be a different variant are excluded rather than counted, so this is a floor on what is out there, not a total.
What to check on a Mazak QTN-200MSY-II
The same list whichever side of the deal you are on.
- Control generation. The manufacturer specifies Matrix Nexus for this model. The control is often the single biggest swing on two otherwise identical machines, because it decides which buyers can use it at all.
- Spindle hours and condition. Most controls show run hours on a maintenance or diagnostics screen. It is the first number anyone asks for, so find it before the conversation rather than during it.
- Tooling and accessories. Holders, chucks, steady rests, probing and automation attachments travel with the machine, and they are worth real money separately from it.
- Turret condition and index time. A turret that has been crashed is the expensive repair on a lathe, and index time is the first thing a buyer times.
- Live tooling and the sub-spindle, if fitted. Whether the rotary tools still drive, and whether the second spindle synchronizes, separates two very different machines that share a model number.
- The tailstock and steady rests. They travel with the machine and they are counted.
- Power and rigging access. How the machine comes out of the building is a real cost, and it is one MTE absorbs, so an accessible machine is worth more to us.
Machines buyers cross-shop with the Mazak QTN-200MSY-II
Other CNC turning centers in this directory, closest first on max turning diameter.
Okuma LB-300
- Swing over bed
- ø530 (ø20.87)
- Max turning diameter
- ø370 (ø14.57)
Okuma L-1420
- Max turning diameter
- 14.17 in / 366 mm
- Max turning length
- 26.06 in (662 mm) on the 650 bed / 49.68 in (1262 mm) on the 1250 bed
Okuma IMPACT LU-15
- Max turning diameter
- 14.17 in / 360 mm
- Max turning length
- 23.62 in / 600 mm
The rest of the CNC turning centers in this directory: DMG MORI NLX 2500SY · DMG MORI SL-35B/1500 · DMG MORI SL-603CMC/2000 · DMG MORI SL-65C · Doosan PUMA 400LC · Mazak HQR-250MSY-850U · Mazak QT-250 · Mazak QTU-350 MY · Mazak SLANT TURN 50N
Browse the whole CNC Lathes catalog, or see everything we buy from Mazak.
Have a Mazak QTN-200MSY-II to sell?
We are the buyer, not a broker. No listing fee, no commission, no waiting for someone else to find a buyer. Quote in 24 to 48 hours, we handle rigging and freight, and we pay at pickup.